Відео

This might be a useful video for when the water level is too high or pump doesn’t run: ua-cam.com/video/SL-MScl53IU/v-deo.htmlsi=DimuPh-0154_e-Qi

Why is there no sound?

You can't leave this out in the rain. The hoppers are not water resistant and the pellet swell up into a nightmare mess once they get wet.

Hi! I need to know if it’s have wifi or Bluetooth?

But what happens when it stops working ???

Who else is here from We Say Things?

You spelled “resturants” wrong. How can we trust this product when your marketing team can’t even spell. Btw, your stove sucks. Provides very little heat and it rusts like crazy, even under a protected patio.

*Vacuum noises*

How do you clean mineral scale in the tornado jets at the top of the bowl?

What I don't understand where do you get the water source from that you have to connect to a water pipe?

What's the point of talking about how quiet it is without actually demoing it

It worked well for a year. Wife was able to jam it with sweet potatoes. Not sure what to do with it at this point. Trash it and get a new one?

What about noise

That is convincing. 😀 I like it. Off to buy a new toilet.

Where can I find them

Kohler must have updated the Cimarron recently bc it has the Revolution 360 swirl flush now

Using the example of sololift2 D-2, I will tell you how to solve problems for a long time. The device has no electronics, the pump is controlled directly by a mechanical switch in the filling sensor, which burns out after 2 years. There is a rubber membrane on the filling sensor, which turns brown over time and stops reacting, it needs to be changed, if it breaks, it will pour through the air duct (a small hole) and the entire pump and possibly a little on the floor, the engine will burn (costs a lot). The air valve becomes dirty and water is poured through it onto the floor. I made the sololift work normally for years without disassembly and cleaning just like that - 1.Close the air valve completely with 3M adhesive tape in 2-3 layers (water will begin to flow in and out of the inlet corrugation by gravity). 2. Turn off the filling sensor and close its air duct (small hole) with acid silicone. 3.Install a configurable capacitive sensor outside the housing to the left of the water tank, for the presence of water, autonics CM30-3015NC (for a 3M double-sided thermal scotch); time relay XY-J02 (JZ-801), OMRON G3MB-202P solid-state relay for shunting the mechanical relay on the time relay board and a 12V power supply and a smoothing capacitor for a 2000 mf psu. The sensor must give a command to turn on the time relay (via a 50mf capacitor, a resistor parallel to the capacitor), which must be configured to turn on once for 3 seconds. The power actuating contacts should go to the wires in the pump that used to fit the filling sensor. Plus, I held a separate switch for manually starting the relay with my time relay and + OMRON. And it is also necessary to conduct a wire for a switch that will turn off the time relay for a short time, turning off the cycle. Setting up the relay - 3s work, 6s simple, number of inclusions 900 times. This will work for a long time and without maintenance with disassembly because there is almost nothing left in the system that can collapse from alkalis or acids, or through which a pump or floor can be filled, the filling sensor does not contact with water, only the engine and the water check valve remain of the vulnerable mechanisms. Once every 3 months, fill the tank with water with detergent for washing and wait 6-24 hours and drain, you can more often (alkaline powder, you can use acid detergent). After closing the air valve, the capacity of the sololift, as well as the outlet pipe, will become pressure. Perhaps, for this reason, may be nothing will accumulate on its walls, just as it does not accumulate on the walls of the outlet pipe due to pressure and cavitation. The instruction was written by Vache Babajanyan

Thanks in a million. Great content. Awesome. Very well explained. I couldn't find this explanation--simply put anywhere else. Great teachers are hard to find. Grade: A++💥

It is very hard to install this celling lamp. The set screw is hard to go through the fixture. It took me three hours and still have not installed it yet. Really bad experience.

Except the 7294 Arbor is not a pull down faucet - pointless video

I am building an outdoor Kitchen and i amthinking about buying this model for it. since i cook alot of fish

BUYER BEWARE: QStoves Q-FLAME Q05C Outdoor Wood Pellet Patio Heater $500 purchased rendered useless after unexpected rain. Manufacturer states they don't advertise as waterproof, provide no additional support for this product. ua-cam.com/video/pE9qb_EkqeM/v-deo.html

Have someone paid for ransom already?

Good and very accurate designs are on the Stodoys website.

non-return valve . nice !

Always wanted a toilet blender...

there goes my dead fish's bones

Or not be high.

The dislikes are from homosaphiens It's super well explained

Nice video! It would be nice if you can add a link to the product in your description.

Can the outlet be connected to a 40 mm pipe (sink pipe) instead of a 4 inch sewer main pipe? I know the direct outlet is 32 mm inches but it goes pressurized, so the question is whether the macerating process is capable of leaving the waste fine enough so it can leave gravitationaly through a 2 inch pipe

What happens on power FAILURE

🌼 Superb ⏏

Does not cover the topic